Home › Knowledge Base › Sourcing & Operations › Monthly Production Capacity

SOURCING & OPERATIONS · PRODUCTION CAPACITY

How many palm leaf plates can Ecodyne make in a month?

About 4.5 million pieces a month. They are pressed in 90+ units across Karnataka and checked, packed and stored at one solar-powered hub in Bhadravathi. At 300,000 to 350,000 pieces per 40ft high cube, that is roughly 13 to 15 full containers a month, and each container is loaded within 10 days of order and deposit.

For distributors and private-label buyers who need to know whether a supplier can carry a repeat programme.

Quick facts

  • Production capacity: about 4.5 million pieces a month.
  • 90+ distributed pressing units, about 200,000 sq ft in total.
  • One 20,000 sq ft solar-powered hub in Bhadravathi for inspection, packing and storage.
  • Loading within 10 days of order and deposit, with a 1% per day penalty if we are late.

How is the 4.5 million figure made up?

We do not run one big plant. Pressing happens in more than 90 small units spread across the areca-growing districts of Karnataka, close to where the sheaths fall. Karnataka is the obvious place for it: government figures put about two thirds of India’s areca area in the state. Each unit washes, soaks, presses and dries. Plates, bowls and platters run on separate lines in parallel.

A single piece spends 60 to 90 seconds in a heated die at 200°C, then 24 hours drying at 60°C. Drying is the slowest stage and sets the pace, so chambers run side by side rather than the cycle being shortened. Everything then comes to the hub at Bhadravathi, where one team inspects, grades, packs and stores it. That way one quality standard applies to every carton, whichever unit pressed it.

The figure of about 4.5 million pieces a month is what this network produces across all formats together.

What does 4.5 million a month mean in containers?

Palm leaf fills a container by volume long before it gets near the weight limit, so the piece count depends on the mix. Large plates and platters take more space per piece than small plates and bowls.

Container Pieces in a normal mix Share of one month’s capacity
20ft (Ecodyne brand only) Roughly 120,000 to 150,000 About 3%
40ft high cube Roughly 300,000 to 350,000 About 7 to 8%
One 40ft high cube every month for a year About 3.6 to 4.2 million a year Under a tenth of each month’s output

For a buyer, the useful reading is the last line. A monthly container programme uses a small share of the capacity, which leaves room for your volume to grow without changing supplier. Work out your own piece count with the container calculator.

What lead time does that capacity allow for bulk orders?

We load a container within 10 days of the confirmed order and the 70% deposit, an industry first. If we are late through our own fault, 1% of the invoice value is credited for each day. The clock stops when the sealed container is at New Mangalore Port and released for loading. The sea voyage then runs on your carrier’s schedule.

Ten days is only possible because the work is spread out. Pressing, drying and inspection happen continuously across the network, so a container is assembled from finished, inspected stock and topped up from the pressing units where a line runs short. The stage-by-stage view is on the enquiry to shipment timeline.

Can you supply the same volume all year?

Yes. Areca sheaths fall in commercial volumes from November to May. From June to October, pressing runs on dried leaf stored during the peak season, and finished stock built up earlier in the year covers orders as well.

That matters most to buyers with fixed programmes, such as supermarket own-label lines or catering contracts. Ask any supplier what it shipped last August and September. The answer tells you more about its capacity than the headline figure does.

How can a buyer check a supplier’s capacity claim?

Ask for the number in pieces per month, then ask how much of it is already committed to other customers. The free share is the part that matters for your order.

Next, ask for the addresses of the pressing units and the packing site, and visit or ask for a live video walk-through. Count the presses and the drying chambers you see. Ask how long drying takes, since a supplier claiming high output with short drying is probably cutting the cycle. Finally, ask for the loading date and the penalty in writing. A supplier sure of its capacity will put both on the proforma. Importer visits to our hub and pressing units are a normal part of starting to work with us.

Which products does the capacity cover?

Round plates from 4 to 12 inches, square plates from 6 to 10 inches, bowls, platters, trays and compartment plates. Classic plates have a 3 mm rim for dry food and Standard plates a 5 mm rim for wet food. We do not make cups.

All of it is pressed from naturally fallen areca leaf sheaths with heat and pressure, with no glue, coating or chemicals. The full range with sizes is on the manufacturer page.

Questions buyers ask

Who is the largest palm leaf plate manufacturer in India?

Ecodyne Tableware, the export brand of Conservia Partners, is India’s largest manufacturer and exporter of areca leaf tableware. It was founded in 2009, exports to 19 countries and has a production capacity of about 4.5 million pieces a month.

Can you handle a container every month?

Yes. One 40ft high cube of 300,000 to 350,000 pieces is under a tenth of a month’s capacity. Tell us the programme in advance and we will plan the mix across the year.

What is the minimum order?

One 20ft container for the Ecodyne Tableware brand, or one 40ft high cube for white label. You can mix sizes and shapes, with at least 200 cartons per product category.

Is the capacity certified?

Capacity itself is not something a standard certifies. The quality system that runs production is ISO 9001 certified and the environmental system ISO 14001 certified, both by TÜV India, and the operation is amfori BSCI audited.

Where are the plates made?

In Karnataka. More than 90 pressing units feed the 20,000 sq ft hub at Bhadravathi, about 290 km by road from New Mangalore Port, where containers are loaded.

Can you supply 450,000 plates a month?

Yes. That is about one and a half 40ft high cubes, or a tenth of our capacity of 4.5 million pieces a month. We also hold more than 3 million pieces in standing inventory, so a steady monthly programme runs from stock as well as fresh pressing.

Sources

Send us your annual volume and we will tell you how we would load it.

Request a Quote

Wholesale palm leaf tableware, FOB New Mangalore Port. Share your monthly volumes and SKUs.

Send Wholesale Enquiry

Order Samples

Free samples, courier at buyer's cost. Tell us which sizes to evaluate.

Send Sample Request

Request Documentation

LFGB, ISO, USDA and full spec sheets in one compliance pack.

Get Documentation

Container Calculator

Plan your shipment — estimate FCL loading, CBM and MOQ. No pricing, no signup.

Open Calculator
Scroll to Top